If you are looking for a tankless unit that can handle large heavy duty applications, look no further. The NC380-SV-ASME-LP can provide hot water to meet the demands of hotels, resorts and housing complexes. A single unit can produce over 13 gallons per minute. With a single system controller, you can connect up to 24 units, which is equivalent to 316 gallons per minute at 9.1 million Btuhs. With its stainless steel casing and ASME accreditation, no other tankless water heater on the market can match its durability and performance. Available in Liquid Propane model.

Noritz NC380-SV-ASME-LP Tankless Water Heater Specifications
Model Name		NC380-SV-ASME-LP
Gas Type		Propane (LP)
Gas Consumption		Max:380,000 BTU/Hr - Min:22,500 BTU/Hr
Thermal Efficiency		84% (LP)
Maximum Hot Water Capacity	45 degree F Rise	13.2 Gal./min.
Capacity Range		0.7-13.2 Gal./min.
Temperature Settings (Deg)		100-150 F (In 5 F intervals),160, 170, 180 F (In 10 F intervals) (14 Options)
Default Temperature Options (Deg)		120,130,140,180 F (Original is 120 F)
Type	Installation	Indoor / Outdoor, Wall Mounted
Type	Air Supply/Exhaust	Power Vented
Connection Sizes	Water Inlet	1 "
	Hot Water Outlet	1 "
	Gas Inlet	3/4"
Power Supply	Supply	120 VAC (60Hz)
Power Supply	Consumption	LP : 142W Freeze Prevention 371W
Materials	Casing	Stainless Steel
	Flue Collar	Stainless Steel
	Heat Exchanger	Copper Sheeting, Copper Tubing
Ignition		Direct Ignition
Operating Pressure		15-150 psi
Minimum Flow Rate		0.7 GPM
Dimensions		29.7"H x 19.1"W x 11.8"D
Weight		106 lbs.
Water Holding Capacity		0.6 Gallon
Safety Devices		Flame Rod, Thermal Fuse, Pressure Relief Valve, Back Pressure Switch, Lightning Protection Device (ZNR), Overheat Prevention Device, Freezing Prevention Device, Fan Rotation Detector
Accessories		Remote Controller, Remote Controller Cord, Anchoring Screws

Noritz NC380-SV-ASME-LP Tankless Water Heater Features:

HRS35 copper heat exchanger casing with special protective coating.
Available in Propane (LP) model.
Thermal Efficiency: 84% (LP)
Warning: PVC cannot be used for venting. Use only Category III (5" stainless steel venting).
Standard Input - gas consumption ranges from 22,500 BTUh to 380,000 BTUh
Compact Design - ANSI Z21.10.3/CSA 4.3 certified design that can be wall-mounted indoors or installed outdoors using optional Vent Cap
Durable Stainless Steel Casing
Heat Exchanger - manufactured with commercial grade copper, 25% thicker piping than standard models
Venting - available in standard power vent model that requires 5" Category III stainless steel pipe
Direct Electronic Ignition
Multi-System Capability - units can be linked together by using either the optional 2-unit Quick Connect or multi-unit System Controller for up to 24 units.
Fully Modulating - BTU input can range from 22,500 to 9.1 million BTUh (for 24-unit Multi-System)
Temperature Controls - includes remote thermostat that can precisely adjust the output temperature from 100 degree F to 180 degree F
Safety Devices - Flame Sensor, Overheat Prevention Device, Lightning Protection Device, Freeze Protection
Five Year Limited Heat Exchanger Warranty for Commercial Use
Five Year Limited Parts Warranty
ASME Certified - all models are certified by ASME and the National Board
Approvals - CSA, UPC, NSF, ASME, Low NOx Approved By SCAQMD (Rule 1146.2)